3027C SSAS

Easy Step By step Configuration of your 3027C SSAS option

First you must create a Hyperlink connection from your PC, you can create a connection by COM port or LAN connection on your PC.


: su sysadm “Enter”

Enter Password: *** “Enter”
Enter New Password: ******** here you must enter your password “Enter”
Confirm new password:******** write again your password “Enter”

Note: after you entered your password (minimum 8 digits) every time you will log onto the terminal to make changes you must write: su sysadm “Enter” and the password which you have configured as indicated above.

Remember you can change the sysadm password again, when you are log in as sysadm level: su  “Enter”  now you can see which level the unit is log in as:
Current user: sysadm 
Please type: password sysadm  “Enter”
Enter new password: ********	
Confirm new password: ********	
Password for user sysadm changed.
:

Now you are ready to input the Fax, Telex, email or SMS details to where the alert message will be sent to as indicated below.




Format: set (space) –am (space) – (entry),(type),{(address),(param)}
Entry can be from 0 to 2 (0,1,2) so total 3 entries
Type has as follows:
0: FOR TELEX SEE EXAMPLE 1
1: FOR FAX AND ADD THE (T30) AT THE END SEE EXAMPLE 2
6: FOR SMS AND ADD THE LES CODE AT THE END SEE EXAMPLE 3
254: FOR EMAIL SEE EXAMPLE 4

	EXAMPLE FOR TELEX

To set up a telex address you type the following:
The command (set  -am) “space” the entry (0, 1, 2) “comma” the type (0) “comma” and then the telex number 5519298 followed by (+/) symbols and the answerback “TATJH” and press (enter) see example below.
: set  –am  0,0,5519298+/TATJH              (enter)

	EXAMPLE FOR FAX

To set up a fax number you type the following:
The command (se  -am) “space”, then the entry code (0, 1, 2) “comma”  then type (1) “comma”  and then the Fax number 4539558888 followed by (t30) and press “enter” see example below.
: set  –am  0,1,4539558888,t30              (enter)

	EXAMPLE FOR SMS

The command (set  -am) “space”, then the entry code (0, 1, 2) “comma” then type (6) “comma” and then the Mobile Number 4525414111 followed by (LES SMS CODE) and press “enter” see example below for TELENOR LES.
: set   –am  0,6,4525414111,66              (enter)
Except France Telecom they have special setting so if you like to use France Telecom use type the following:
: set   –am  0,6,SMS+4525414111,29             (enter)

SEE LES SMS CODES BELOW:

TELENOR LES USE CODE (66)
XANTIC LES USE CODE (696)
FRANCE TELECOM USE CODE (29)
STRATOS LES USE CODE (696) 

Remember lock the unit to the LES you want to use for the SMS service with the command set –m:

Please check EXAMPLE FOR ENTERING THE PREFERRED LESO


: set -m 4,104,204,304


: SEt -m ALL_OCEANS

Alert LES for ocean 0     : 4
Alert LES for ocean 1     : 104
Alert LES for ocean 2     : 204
Alert LES for ocean 3     : 304
:




	EXAMPLE FOR EMAIL

To set up an email address you type the following:
The command (set  -am) “space”, then the entry code (0, 1, 2) “comma” then type (254) “comma” and then the email address ssasalert@tt.dk and press “enter” see example below.
: set –am  0,254,ssasalert@tt.dk               (enter)

Multiple addressing of the SSAS alert.

You can add more then one address at the same line for the E-mail and Fax service, 
Max 79 characters per line.
You can NOT do it for SMS service, please see below.

: set -am

Update time: 2006-05-18  10:27:41
Entry  Type  Param  Address
    0   254         qwer@thrane.com;tyui@thrane;asdf@thrane.com
    1     1    t30  4539551234;4539555678;4539550987
    2     6     66  4525414111

To set/clear addresses: set -am <Entry>,<Type>[,<Addresses>[,<Param>]]
:

Routing of Covert Alert Messages and Test Messages.


By using the command line set –ame <Entry><Msg. Type><Enter> it is possible to configure to which addresses the alert messages and test messages should be routed.
However, please notice the alert message always should be configured so it is received by the addresses 0 and 1. The test message can optional be routed to the addresses 0 and 1 additionally.
The address no. 2 is fully user programmable for alert messages, test messages or both.
	

Message Types:

1 = Alert		(only message)
2 = Test		(only test)
3 = Alert + Test	(message+test)


Examples:

The first address (0) is set to receive alert messages only:
: set –ame 0,1<Enter>

The second address (1) is set to receive both alert- and test messages:
: set –ame 1,3<Enter>

The third address (2) is set to receive test messages only:
:set –ame 2,2<Enter>


Note:
If an illegal, combination of parameters is used, following error code will appear:
:set –ame 0,2<Enter>
ERROR 121: Bad parameter(s)


	EXAMPLE FOR ENTERING THE TERMINAL ID NUMBER

To set up the terminal ID number you type the following:
The command (set   -u) “space”, then the ID NUMBER and press “enter” see example below.
: set –u  422380021               (enter)

	EXAMPLE FOR ENTERING THE PREFERRED LESO

To set up the preferred LESO you type the following:
The command (set -m) “space”, then the LESO CODES and press “enter” see example below for Telenor.
: set –m 4,104,204,304               (enter)




Land Earth Stations Operators covering all 4 ocean regions.




: set -m ALL_OCEANS

Alert LES for ocean 0     : 4
Alert LES for ocean 1     : 104
Alert LES for ocean 2     : 204
Alert LES for ocean 3     : 304
:



	EXAMPLE FOR ENTERING ADDITIONAL TEXT BELOW THE MESSAGE

To Add Text below the Message send from the Terminal you type the following:
The command (set -at) “space”, then the Text in inverted commas and press “enter” see example below.
: set  -at  ”Vessel Cape Norton”               (enter)


Up to 199 characters in the free ALERT text in software version 2.12
Please type your text in Notepad, whit the tr command before the text:



dir
IOPORT TXT 75 04-08-19 08:24
_EGCLOG 0 04-08-19 08:24
_TXLOG 730 04-08-19 08:24
_RXLOG 41 04-08-19 08:24
4 File(s) 171988 bytes free
: tr long.txt (Ctrl+V) tr long.txt
Ship Name: M/S Thrane & Thrane
Ship Owner: Thrane & Thrane
Flag State: Denmark
Code 1:12345678
Code 2:abcdefgh
:
: dir
IOPORT TXT 75 04-08-19 08:24
_EGCLOG 0 04-08-19 08:24
_TXLOG 730 04-08-19 08:24
_RXLOG 41 04-08-19 08:24
long txt 114 04-08-27 11:10
5 File(s) 171740 bytes free
:
: se -atf long.txt (Ctrl+V) tr long.txt
: Ship Name: M/S Thrane & Thrane
ERROR 120: Invalid command
: Ship Owner: Thrane & Thrane
ERROR 120: Invalid command
: Flag State: Denmark
ERROR 120: Invalid command
: Code 1:12345678
ERROR 120: Invalid command
: Code 2:abcdefgh
: se -atf
Current text:
Ship Name: M/S Thrane & Thrane
Ship Owner: Thrane & Thrane
Flag State: Denmark
Code 1:12345678
Code 2:abcdefgh